Out of stock

Checktemp® 4 Folding Thermometer – HI151-Red-Yes

The HI151 Checktemp® 4 is a folding thermistor thermometer that can measure temperature up to 300 ℃ (572 ℉). These thermometers offer many advanced features including CAL-Check for an internal verification of the electronics and a motion sensor which eliminates the need of closing and reopening the probe when the meter enters a power saving mode. The Checktemp 4 is available in six different colors which can be assigned to different products to avoid cross contamination in the restaurant, kitchen or production facility.

  • CAL Check to verify meter performance
  • Waterproof to IP67 Standards
  • Wake on motion

AED

Estimated delivery: 20 - 21 May

SKU:HI151-100
HI151 Checktemp 4 Temperature Tester

Ergonomic Design with Rubberized Grip

Checktemp® 4 has an ergonomic design that fits comfortably in the hand. The meter uses vulcanized rubber that is available in 6 different colors for a non-slip grip.

Waterproof Durable Casing

The Checktemp thermometer is completely waterproof to IP67 standards. The IP67 standard is for continuous immersion in water up to 1 meter (3′) in depth. The meters will actually float if accidentally dropped into a pot, vat or any other container.

Penetration Probe

The sharp, AISI 316 stainless steel probe is ideal for testing fresh, cooked and semi frozen food. The NTC thermistor is located in the sensing tip and allows for the measurement of food that is 2 cm (0.79″) thick.

HI151 Checktemp 4 Temperature Tester

Instrument Quality Certificate for Traceability

HI151 is calibrated to five points (-20.0, 0.0, 25.0, 60.0 and 120.0 ℃) and tested at three points using reference meters, the accuracy of which is traceable to NIST in the USA or an internationally acceptable national physical standards. Each meter is serialized and supplied with an instrument quality certificate

CAL-Check

With all thermometers there is drift in the electronics over time. Every time the thermometer is switched ON the LCD will display “CAL” then “-0-”, indicating that the factory calibration has been verified and the thermometer is ready for use.

Wake on Motion Sensor

The meter has an adjustable power save mode that can be disabled. The power save mode can be programmed to turn the display off and conserve power after 1, 2, 8, or 60 minutes. The built-in motion sensor detects when the meter is picked up and automatically turns the display back on.

Checktemp®4 Temperature Tester – HI151

HI151 Checktemp®4 Temperature Tester Family

Specifications

SKU HI151-100
Name Checktemp® 4 Folding Thermometer – HI151-Red-Yes
Thermistor Temperature Range -50.0 to 300 °C / -58.0 to 572 °F
Thermistor Temperature Resolution 0.1 °C (-50.0 to 199.9 °C); 1 °C (200 to 300 °C)
0.1 °F (-58.0 to 199.9 °F); 1 °F (200 to 572 °F)
Thermistor Temperature Accuracy ± 0.2 °C (-30.0 to 170.0 °C); ± 0.4 °C (-50.0 to -30.0 °C and 170.0 to 199.9 °C); ± 1 °C (200 to 300 °C) ± 1 digit
±0.4 °F (-22.0 to 199.9 °F); ±0.8 °F (-58.0 to -22.0 °F);
±1 °F (200 to 392 °F); ±2 °F (392 to 572 °F) ± 1 digit
Automatic Shut-Off power save settings: 1 min, 2 min (default), 8 min, 60 m in. or OFF
Battery Type/Life CR2032 3V x 2 pcs. / approx. 4000 hours of use
Environment -20.0 to 50.0 ºC (-4.0 to 122.0 ºF)
Dimensions 165 x 45 x 24 mm (6.5 x 1.8 x 0.9”)
Weight 85 g (3.0 oz)

Ordering Info

HI151 Checktemp 4 is supplied with batteries, quality certificate, and instruction manual.

Manuals

Checktemp® 4 Folding Thermometer – HI151-Red-Yes

Bestsellers

Digital Glass Body pH Electrode for General Purpose - HI11310

601 AED
The HI11310 is a glass body refillable double junction pH electrode with a built-in temperature sensor for temperature compensated measurements in a single probe design. This probe connects to the meter with a 3.5 mm connector. The 3.5 mm connector is proprietary to meters that use digital electrodes. The HI11310 electrode features a built-in microchip that stores sensor type, serial number, and calibration information. It also features a single ceramic junction and the spherical pH sensing portion is made with high temperature glass. This design consideration is ideal for general purpose laboratory use.
  • Built-In Microchip
  • Spherical Glass Tip
  • Double Junction Reference
  • 3.5 mm Connector

Refillable Combination pH Electrode with BNC Connector - HI1131B

543 AED
The HI1131B is a glass body, refillable, double junction pH electrode with a BNC connector. This electrode has a single ceramic junction in the outer reference cell and the spherical pH sensing portion is made with high temperature glass. This design consideration is ideal for laboratory samples, beer and other liquid samples, as well as general purpose use.
  • Refillable Electrode
  • Double Junction Design
  • High Temperature (HT) Glass

Portable pH/EC/TDS/Temperature Meter - HI9811-51

710 AED
The HI9811-51 is an economical, wateproof, portable meter that measures pH, conductivity (EC), total dissolved solids (TDS) and temperature (℃) with a single probe. The meter operation is simplified with dedicated buttons for measurement modes to be be displayed on the LCD and knobs for single point calibration of pH and EC/TDS. The HI9811-51 is most suitable for agricultural, greenhouse and hydroponic applications.
  • 3 in 1 probe with pH, EC/TDS and temperature sensors
  • Amplified pH electrode for immunity to electrical noise including from ballasts and pumps
  • Large LCD with instructions

Digital Glass Body pH Electrode with Matching Pin for General Purpose - HI11311

681 AED
The HI11311 is a glass body, refillable, double junction pH electrode with a matching pin and a built-in temperature sensor for temperature compensated measurements in a single probe design. This probe connects to the meter with a 3.5 mm connector. The 3.5 mm connector is proprietary to meters that use digital electrodes. The matching pin integrated into the HI11311 is for the Sensor Check™ capability of the edge pH meter; this feature is used to identify problems with the pH electrode such as cracks in the sensing glass or poor condition of the reference junction. The HI11311 electrode features a built-in microchip that stores sensor type, serial number, and calibration information. It also features a single ceramic junction and the spherical pH sensing portion is made with high temperature glass. This design consideration is ideal for general purpose laboratory use.
  • Matching Pin for enabling Sensor Check feature that alerts to a broken electrode or clogged junction
  • Double Junction Reference
  • 3.5 mm Connector

Marine Phosphate Ultra Low Range Checker® HC - HI774

223 AED
The Hanna Phosphate Ultra Low Range (0.00 to 0.90 ppm) Checker® bridges the gap between simple chemical test kits and professional instrumentation. Chemical test kits have limited accuracy and resolution since they rely upon the human eye to discern differences in color. Professional instrumentation incorporates a light source such as an LED or tungsten lamp with a filter and a light-sensing detector to precisely determine ion concentration. Professional instrumentation offers greater resolution and accuracy but can cost hundreds of dollars. The Hanna Phosphate Ultra Low-Range Checker® uses a fixed wavelength LED and silicon photo detector to provide the accuracy of professional instrumentation at the affordable price of a chemical test kit.
  • Compact, Portable Design
  • Built-in Timer
  • One-Button Operation

DiST® 6 EC/TDS/Temperature Tester (0.00 to 20.00 mS/cm) - HI98312

412 AED
When the original DiST® (Dissolved Solids Tester) was first introduced, conductivity and total dissolved solids measurements became easy and affordable. The DiST’s ease of use, in combination with it’s affordability, made it the standard in EC and TDS measurement. Hanna continues the standard in EC and TDS testing with the DiST®6.
  • Waterproof
  • Exposed temperature probe for fast response
  • High range EC/TDS 0.00 to 20.00 mS/cm 0.00 to 10.00 ppt (g/L)

HI7031L/C 1413 µS/cm Conductivity Standard (500mL Bottle)

81 AED
HI7031L/C is a premium quality 1, 413 µS/cm conductivity standard that is prepared against a NIST traceable potassium chloride solution and supplied with a certificate of analysis. Hanna conductivity solutions have the lot number and expiration date clearly marked on the label and are air tight with a tamper-proof seal to ensure the quality of the solution. Hanna’s line of conductivity standards have been specially formulated to have an expiration of 5 years from the date of manufacture for an unopened bottle.
  • Supplied with Certificate of Analysis
  • Temperature chart of the actual µS/cm value at various temperatures printed on each bottle
  • Air tight bottle with tamper-proof seal to ensure quality
Back to Top
img
Product has been added to your cart